Ultra-silent TMC2100 V1.3 Stepper Motor Driver Module SPI With Plug Type Stepstick Smoother Kit For 3D Printer Board

Ultra-silent TMC2100 V1.3 Stepper Motor Driver Module SPI With Plug Type Stepstick Smoother Kit For 3D Printer Board

Image
Available: In Stock
$16.37 USD
Wishlist Compare
Ultra-silent TMC2100 V1.3 Stepper Motor Driver Module SPI With Plug Type Stepstick Smoother Kit For 3D Printer BoardTMC2100 V1.3 Stepstick Stepper Motor Driver

Feature:
Drive current algorithm and regulation:
1. drive current algorithm: i=Vref*1.9/2.5, the default Vref about 0.65v, so the default current 0.5A, the maximum current 1A
2. Vref measurement of Gnd and potentiometer intermediate voltage.
3. Don’t connect to the motor when measuring voltage, otherwise it is easy to burn the drivers.
4. the measurement of the voltage should be switched on. Don’t just connect the USB power supply.
Attention: please put TMC2100 drivers in the correct direction on the board.


Use of the TMC2100 drive module:
1. When use in the Ramps1.4 or MKS Gen, or Lerdge touch screen motherboard, please remove the 3 jumper cap under the socket.
2. Please pay attention to direction.
3. The heat sink directly attached to the PCB.
4. The motor direction is opposite to that of A4988 and DRV8825, please adjust the firmware or adjust the motor wiring if you want to change to 4988. And if you use the Lerdge motherboard, please set the direction directly in the setting page of direction of the motor.



Stepstick Smoother

Description:
This smoother is mainly for the elimination of printed marks produced by 3D printers and the parallel arm structure, can effectively eliminate low-speed non-uniform waveform signal so as to achieve a relatively flat signal waveform.

Features:
1. Plug and play, no wiring required
2. Effective to use



Package Included:

1x TMC2100 V1.3 Stepstick Stepper Motor Driver 
1x Stepstick Smoother

1x Heat sink
1x Screwdriver

As shown in the figure: If you need to adjust the mode of the 2100 module, you need to use the soldering iron, according to the table will be listed in the corresponding pin and adjacent pad can be connected.










Ultra-silent TMC2100 V1.3 Stepper Motor Driver Module SPI With Plug Type Stepstick Smoother Kit For 3D Printer BoardTMC2100 V1.3 Stepstick Stepper Motor Driver

Feature:
Drive current algorithm and regulation:
1. drive current algorithm: i=Vref*1.9/2.5, the default Vref about 0.65v, so the default current 0.5A, the maximum current 1A
2. Vref measurement of Gnd and potentiometer intermediate voltage.
3. Don’t connect to the motor when measuring voltage, otherwise it is easy to burn the drivers.
4. the measurement of the voltage should be switched on. Don’t just connect the USB power supply.
Attention: please put TMC2100 drivers in the correct direction on the board.


Use of the TMC2100 drive module:
1. When use in the Ramps1.4 or MKS Gen, or Lerdge touch screen motherboard, please remove the 3 jumper cap under the socket.
2. Please pay attention to direction.
3. The heat sink directly attached to the PCB.
4. The motor direction is opposite to that of A4988 and DRV8825, please adjust the firmware or adjust the motor wiring if you want to change to 4988. And if you use the Lerdge motherboard, please set the direction directly in the setting page of direction of the motor.



Stepstick Smoother

Description:
This smoother is mainly for the elimination of printed marks produced by 3D printers and the parallel arm structure, can effectively eliminate low-speed non-uniform waveform signal so as to achieve a relatively flat signal waveform.

Features:
1. Plug and play, no wiring required
2. Effective to use



Package Included:

1x TMC2100 V1.3 Stepstick Stepper Motor Driver 
1x Stepstick Smoother

1x Heat sink 1x Screwdriver
As shown in the figure: If you need to adjust the mode of the 2100 module, you need to use the soldering iron, according to the table will be listed in the corresponding pin and adjacent pad can be connected.